Boson NetSim 8.0 (Full Version)
Boson NetSim 8.0 (Full Version) | 87.34MB | RAR | Patch included
minimum requirements – Windows XP
minimum requirements – Windows XP
NetSim for CCNP 8.0 is designed to help you learn the Cisco IOS command structure, and it supports the technologies and skills required for the recently revised CCNP certification.
NetSim for CCNP includes new labs for the ROUTE, SWITCH and TSHOOT technologies. In addition to new content, NetSim for CCNP 8.0 contains a new and improved interface that makes completing labs, compiling new labs and designing network topologies easier than ever before. The network topology, device consoles and lab instructions can share the screen in NetSim 8.0 with easy-to-use panes. NetSim 8.0 also supports multiple monitors.
Everything you need to create and compile new labs – from the NetMap topology designer, to the device configuration window, to the saving and merging of files – are all in one easily navigable window. Completing NetSim labs and creating your own labs have never been so easy.
Additional Resources
NetSim 8.0 User Manual. (Best viewed when using Acrobat viewer.)
How to compile a lab using NetSim 8.0. (PDF)
NetSim for CCNP 8.0 Enhancements
- Vastly improved user interface
- External lab document viewer enables the use of multiple monitors
- Telnet mode enables the user to open a separate Telnet session for each device in the simulated topology
- New labs supporting ROUTE, SWITCH and TSHOOT technologies
- Supports EIGRP debugging
- Improved EIGRP – less processor intensive
- Support for HSRP, MHSRP and VRRP
- Hands-on experience without the hardware
- A Network Designer that supports 42 routers and 6 switches
- Up to 200 devices per network
- Virtual Packet Technology: software-created packets that are routed and switched through the simulated network
- The ability to populate the WAN slots with a broad range of Network Modules
- A Telnet mode that allows you to configure devices in the simulated topology using the Windows telnet program
- The functionality of a full rack of equipment on your laptop
- Automatic lab-grading capability
- The ability to load and save your network configurations
- The ability to paste real router configurations into the devices
- The ability to configure your own ISDN and Frame Relay switch mappings
- The benefit of connecting your devices over simulated WANs without expensive ISP gear
- Support for IPv6 addressing
- 42 Routers (Cisco devices)
- 6 Switches (Cisco devices)
- 5 PCs: TFTP, Traffic generator, AAA Server, VPN Client, workstation
- 1 IP Phone
- 48 total Cisco devices
- 54 total devices
- Configuring EIGRP III
- EIGRP and Frame Relay
- Influence EIGRP Path Selection
- Optimizing EIGRP
- EIGRP Authentication
- Configuring Hot Standby Router Protocol
- Configuring Virtual Router Redundancy Protocol
- Configuring Multiple Hot Standby Router Protocol
- Troubleshooting EIGRP Routing
- Troubleshooting Hot Standby Router Protocol
- Configuring Hot Standby Router Protocol (HSRP)
- Configuring Virtual Router Redundancy Protocol (VRRP)
- Configuring Multiple Hot Standby Router Protocol (MHSRP)
- 2950 Deleting VLANs
- 2950 IP Addresses
- 2950 Spanning Tree
- 2950 Telnet
- 2950 Trunk
- 2950 VLANs
- 2950 VTP
- 2950 VTP with Client
- AAA
- AAA Login Authentication and Exec Authorization
- Access List Review
- Address Optimization
- Advanced Access Lists
- Advanced Router Config
- Applying Security Tools
- ARP
- Backing up a WAN Connection with IPSEC VPN
- Backup Interface
- Backup Using TFTP
- Basic Router Config
- Basic Show Commands
- BGP
- Catalyst 1900 Switch Config
- Catalyst 2950 Switch Config
- CDP
- CHAP and RIP
- Cisco Discovery Protocol – Router
- Configuring a Switch for a WLAN
- Configuring Class-Based Header Compression
- Configuring EIGRP I
- Configuring EIGRP II
- Configuring EIGRP III
- Configuring FIFO and WFQ Queuing Mechanisms
- Configuring Frame Mode MPLS
- Configuring GRE Tunnels over IPsec using SDM
- Configuring Hot Standby Router Protocol
- Configuring IOS Security Part 1 – VLAN ACL’s
- Configuring IOS Security Part 2 – TACACS+
- Configuring IPv6
- Configuring IPv6 Routing
- Configuring IPv6 Tunnels
- Configuring LFI
- Configuring Multiple Hot Standby Router Protocol
- Configuring NBAR
- Configuring OSPF
- Configuring QoS
- Configuring QoS Preclassify
- Configuring QoS with Cisco AutoQoS
- Configuring Router Interfaces
- Configuring Static and OSPFv3 Routing
- Configuring Support for IP Telephony
- Configuring Switch Interfaces
- Configuring the LLQ Queuing Mechanism
- Configuring Virtual Router Redundancy Protocol
- Connectivity Test with TraceRoute
- Creating a Host Table
- Default Routes
- Demo Lab
- EIGRP and Frame Relay
- EIGRP and Wildcard Masks
- EIGRP Authentication I
- EIGRP Authentication II
- EIGRP Routes
- Extended Access Lists
- Extended Access Lists with RIP
- Frame Relay
- Frame Relay Full Mesh
- Frame Relay Hub-and-Spoke
- Frame Relay with Dial Backup
- Hierarchical IP Addressing
- IGRP
- IGRP Routes
- Implementing Multiple Spanning Tree Protocol
- Implementing NAT
- Implementing NAT II
- Influence EIGRP Path Selection
- Inter VLAN Routing
- Initial Config
- Introduction to MQC and the SDM QoS Wizard
- IOS Switching Initial Configuration
- IP Access Lists
- IP Addressing
- IPSEC
- ISDN
- ISDN BRI
- ISDN BRI-BRI Using Dialer Profiles
- ISDN BRI-BRI Using Legacy DDR
- ISDN Dialer Profiles
- ISDN PRI Using Dialer Profiles
- IS-IS
- Lab Primer
- Layer 3 Switching
- Layer 3 Switching and Layer 2 Security
- Loopback Interfaces
- Low Latency Queuing
- Many-to-One NAT
- Multi-Area OSPF
- Multi-Area OSPF and Routing Table Optimization
- Multicast Routing
- Multi-Site Frame Relay and Policy Routing
- Multi-Site Network
- Named Access Lists
- NAT
- 640-802 CCNA
- 640-822 ICND1 (Interconnecting Cisco Networking Devices Part 1)-CCENT
- 640-816 ICND2 (Interconnecting Cisco Networking Devices Part 2)-CCNA
- 642-813 SWITCH-CCNP
- 642-832 TSHOOT-CCNP
- 642-902 ROUTE-CCNP